Announcement

Collapse
No announcement yet.

"Dual Height" Cheek Rest for Drillings or Combo Guns

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • "Dual Height" Cheek Rest for Drillings or Combo Guns

    This unique "Dual Height" cheek rest might be very helpful for those who shoot Drillings, Combination Guns, rifles or slug shotguns with/without a scope based on conditions or the game.

    I'm finalizing all the work needed on that pre-war German Blitz Trigger-plate Drilling I bought at a low price (as it had a split stock, a deep gouge in the buttstock and firing pin indicator pins that didn't work) that I've posted about here before. I've fixed the split stock and completed all the action work, and as I get closer to sighting it in I've realized it has more drop than I want/like, plus it also has claw mounts for a high-mounted scope which makes getting a good cheek weld next to impossible.

    I think I've stumbled onto an excellent solution -- a "dual height" cheek rest called the "Accu-Riser Molded Cheek Rest" which has a hard nylon base onto which a 5/8" tall or 1" tall rubber cheek pad (insert) can be easily added. I got it off of eBay.

    As I will plan to shoot some trap with the left barrel of the Drilling the lower insert will work well for that, or for when I use it without the scope:



    (You can also see I added one of those small rubber bumpers on the rear of the trigger guard, as I do with all my double-trigger side-by-sides; they do help if a large number of rounds are fired.)


    And for those times I'll hunt with it with a 1.5 - 6X German Hensoldt-Wetzlar scope attached, the taller 1" insert will be used:
    (The lower insert is in the bottom of the image for comparison)




    I've completed fitting a .22 Mag barrel 9" barrel insert (an "Einstecklauf" made by Krieghoff) into the right shotgun chamber/bore and it has been function-fired just fine, so now I can sight-in the scope to the lower 8x57JRS barrel (at 75 or 100 yards) and then adjust the 22 Mag Einstecklauf to match the scope at 50 yards. (That's the current plan anyway.)

    This is a view of the open breech -- those 3 loads are very versatile and will handle anything I could encounter in the fall woods of Maine:




    The cheek rest comes with a Velcro strap and double-sided tape for semi-permanent installation, but it also allows 2 screws from the top (under the inserts) to be used for permanent mounting. I'll plan to do that as the fit of the base to the buttstock's curves is perfect, and I need the ability to use both rubber inserts, plus the base itself hides a deep ugly gouge on the other side of the stock (which was another reason why I got the gun for less than market price).

    Waidmannsheil. Tight groups!

    Old No7
    Last edited by Old No7; 04-27-2020, 09:48 PM.
    "Freedom and the Second Amendment... One cannot exist without the other." © 2000 DTH

  • #2
    Old No7,
    See my comments on Double Gun Forum.
    Mike

    Comment


    • #3
      I like that picture of the three different cartridges in the chambers of your drilling. That is exactly what I am doing with mine. I am presently working on a 16 gauge slug load for the left shot barrel. No, they are not Brenneke slugs, but a very good imitation. It's called the dangerous game slug, DGS, and sold by Ballistic Products Inc. So far I have it hitting the 102 yard spot within about 6 inches where the 193 grain factory S & B ammunition strikes.
      I also have a ~195 grain cast bullet that I powder coat and then add a copper gas check. So there is more experimentation coming with the 9.3 barrel.
      Peter

      Comment


      • #4
        Peter,
        That seems like pretty good results at 102 yds. If you try the slugs at 50-60 yds. , you may have a useable point of impact already.
        Mike

        Comment


        • #5
          I?m glad you like that cheek pad. I?m the one who designed and make them . I have other models of cheek pads and leather butt pads I make as well. I use my neoprene model on some of my German guns that I have mounted scopes on. I don?t use see through mounts so the scopes aren?t as high as the original claw mounts but you still need some extra height added to the comb to get a proper line of sight with the scope.

          Comment


          • #6
            I?ll add I don?t sell them on EBay. A friend of mine does that. I have websites ( accu-riser.com and black powder bags.com)

            Comment


            • #7
              Originally posted by mike ford View Post
              Peter,
              That seems like pretty good results at 102 yds. If you try the slugs at 50-60 yds. , you may have a useable point of impact already.
              Mike
              I'll definitely work on the curvature of the flight so that I will know how high the slug is traveling above the line of sight at intermediate distances. These old guns are a lot of fun and very versatile.
              Peter

              Comment


              • #8
                Originally posted by Leatherman View Post
                I?m glad you like that cheek pad. I?m the one who designed and make them . I have other models of cheek pads and leather butt pads I make as well. I use my neoprene model on some of my German guns that I have mounted scopes on. I don?t use see through mounts so the scopes aren?t as high as the original claw mounts but you still need some extra height added to the comb to get a proper line of sight with the scope.
                Thanks for posting. It's a great product and is working well for me -- it does just what I want it to do.

                Oh, and I have some of your excellent leather muzzleloading accessories too. Those are also top quality.

                Tight groups.

                Old No7
                "Freedom and the Second Amendment... One cannot exist without the other." © 2000 DTH

                Comment

                Working...
                X